| FD-USB-1GB |
 |
|
|
| |
| FD-USB-1GB-Debian |
|
|
|
1GB USB Flash Drive with Debian preinstalled. |
|
| |
| DLP-TEMP-G |
|
|
|
DLP-TEMP-G is a USB/microcontroller based 3-channel data-acquisition system preprogrammed with firmware for digital I/O or reading digital temperature-sensing devices. The DLP-TEMP-G board is equipped with a Type A male USB connector for direct connection to a USB port. No cable is required unless the board is to be located away from the PC, in which case a user supplied USB A-A (male-female) extension cable can be used. |
|
| |
| DLP-IO8-G |
|
|
|
DLP-IO8 Data Acquisition Module is a low-cost, easy-to-use data acquisition system for measuring voltages, controlling and monitoring processes, and acquiring temperature data. Each of the 8 available channels can be configured for any of the digital, analog, or temperature modes via single-byte commands. All operational power is taken from the host PC via the USB port. |
|
| |
| DLP-TILT-G |
|
|
|
The DLP-TILT-G USB Accelerometer Module has four primary applications: (1) vibration analysis, (2) tilt sensing, (3) AC signal analysis, and (4) two-button mouse pointing device alternative. |
|
| |
| DLP-UTH8 |
|
|
|
DLP-UTH8 is a low-cost, easy-to-use active hub used for connecting multiple temperature and humidity sensors to one PC featuring 4th generation USB silicon from FTDI. All operational power is taken from the host PC via the USB port. The temperature and humidity sensor modules (shown below) connect to the DLP-UTH8 using standard CAT5 ethernet cable. |
|
| |
| DLP-TH1 |
|
|
|
USB Temperature/Humidity Sensor |
|
| |
| DLP-UT1 |
|
|
|
| |
| DLP-RFIDTAG |
|
|
|
10-Pack of 13.56MHz RFID Transponder tags. |
|
| |
| DLP-RFID1 |
|
|
|
DLP-RFID1 is a low-cost, USB-powered module for reading from and writing to ISO 15693, ISO 18000-3, and Tag-it™ intelligent RFID transponder tags. It has the ability to both read and write up to 256 bytes of data in addition to reading the unique identifier (UID/SID). All of the DLP-RFID1's electronics and antenna reside within the compact unit, and all operational power is taken from the host PC via the USB interface. The range of the internal antenna is up to 4 inches depending upon the size of the tag being read. |
|
| |
| DLP-RF1-Z |
|
|
|
The DLP-RF1-Z combines a USB interface, Freescale™ MC13193 2.4GHz Direct-Sequence Spread Spectrum RF Transceiver IC and Freescale MC9S08GT60 microcontroller to form an IEEE 802.15.4 compliant, ZigBee™ ready, short-range transceiver module. |
|
| |
| CBL-USB-COM-1 |
|
|
|
This cable is suitable for adding one RS232 serial port to your computer. It works with both USB 1.X and USB 2.0 ports |
|
| |
| WUA-1340 |
|
|
|
D-Link Wireless G USB Adapter. |
|
| |
| DUB-E100 |
|
|
|
D-Link DUB-E100 USB 2.0 10/100 Ethernet Adapter. |
|
| |
| MD300 |
|
|
|
MD300 Mobile Broadband USB Modem |
|
| |
| BRD-USB-RS232-TTL-1 |
|
|
|
The USB converts USB to TTL level RS232 signals. Ideal for microcontroller circuits. The design uses FTDI FT232BM/BL chip. |
|
| |
| BRD-USBXB-1 |
|
|
|
It is the most easiest and reliable way to connect the Xbee module to a PC via USB port |
|
| |
| DLP-IOR4 |
|
|
|
The DLP-IOR4 is a low-cost, easy-to-use relay module utilized for computer control of electrical or electronic equipment. |
|
| |
| K38021US |
|
|
|
Rechargeable battery pack. AC power adapter with USB allows you to recharge your battery pack. |
|
| |
