PCARD-1
Low cost PIC® Programmer
Peripheral Boards
Find By Type:
- All
- Memory
- Data Acquisition (D/A, A/D, Sensors)
- Display
- Communications
- Control
- Other
- Robotics
- Breakout Boards
- USB Peripherals
MMC-RTC-1
MMC-RTC-1 board is designed specifically for storage/data logger applications. A Multi Media Card (MMC) with high capacities such as 1 Gigabyte can be installed on the built-in MMC socket. MMC-RTC-1 board also includes a DS1307 low power, battery-backed Clock/Calendar. ( Multi Media Card is not included )
Details
RAM-1
Memory peripheral board with 512 Kbyte static RAM and 512 Kbyte flash memory with an access via 8-bit address/data multiplexed bus. Ideal for data storage and web server applications
Details
T-1-1820
T-1-1820 board is a digital temperature sensor peripheral board for MINI-MAX and other micro-controller systems.
Details
TH-1-SHT
TH-1-SHT board is a digital temperature/humidity sensor peripheral board for MINI-MAX and other micro-controller systems.
Details
TB-1
Training Board allows performing various experiments with most microcontrollers. TB-1 has programmable traffic lights, 4-channel, 8-bit analog inputs, buzzer, switch inputs, and counter/timer inputs to test the interrupts
Details
DAQ-2543-DA-1
DAQ-2543-DA1 is an ADC/DAC peripheral board with 11 channels of 12-bit analog inputs and one channel of 10-bit analog output.
Details
DAQ-128
DAQ-128 is 8-channel, 12-bit, Analog Input and 1 channel, 10-bit Analog Output peripheral boards. DAQ-128 has +/- 4 Volt input range
Details
DAQ-127
DAQ-127 is 8-channel, 12-bit, Analog Input and 1 channel, 10-bit Analog Output peripheral boards. DAQ-127 has +/- 10 Volt input range
Details
THERMOCOUPLE-1
1 channel thermocouple board with cold-junction compensation and amplification for any combination of type E,J,K,R,S,T thermocouples. Use with DAQ-2543 or DAQ-128 boards
Details
THERMOCOUPLE-4
4 channel thermocouple board with cold-junction compensation and amplification for any combination of type E,J,K,R,S,T thermocouples. Use with DAQ-2543 or DAQ-128 boards
Details
DAC-8
DAC-8 is a 10-bit Digital to Analog Converter (DAC) board with I2C 2-wire interface. DAC-8 has 8 analog output channels.
Details
OLED-1
128x64 4-bit Grayscale OLED Graphics display board with microcontroller serial (SPI) interface
Details
LED-1
A peripheral board with four 7- segment LED displays with decimal point. The displays are placed on sockets and can be easily replaced. All 4 digits on the board is controlled via an I2C 2-wire serial bus
Details
CB-1
CB-1 is a wireless communications peripheral board for the MINI-MAX series of micro-controller systems. CB-1 provides Infrared ( IrDA ), Zigbee, Bluetooth communications for a host microcontroller.
Details
UART-2RS232
UART-2-RS232 has two RS232 channels and two (optional) RS485 channelsand a hardware I2C bus for communications with a host microcontroller.It translates data from I2C to RS232/RS485 and adds more serial portsto MINI-MAX boards or other microcontroller systems.
Details
X10-1
Connects MINI-MAX/51-C to standard X10 devices through the TW523 Power line interface.
Details
TW523
TW523 is a two-way X10 power line interface module. TW523 allows both control and monitoring of X10 devices with microcontrollers.
Details
BRD-RS232-TTL-1
RS232 to TTL Converter.
For use with converting the RS232 port of MINI-MAX boards, PC's or any other RS232 devices to/from TTL/CMOS level.
Details
MOTOR-1B
A universal stepper motor controller board for BiPOM MINI-MAX series microcontroller boards and other microcontroller systems. It supports unipolar and bipolar stepper motors up to 750 mA of coil current at up to 30 Volts.
Details
DIO-1
I/O expander board with 8 open/collector outputs ( each capable of 400mA ) and 12 TTL/CMOS inputs/outputs. DIO-1 has a PIC16C62 micro-controller that acts as a I2C 2-wire slave device can also be used as a standalone PIC micro-controller board.
Details
MOTOR-2
MOTOR-2 controls simultaneously 2 bipolar or unipolar stepping motors with phase currents up to 2.5A. MOTOR-2 can be used as a stand-alone microcontroller board or as a motor controller peripheral board.
Details
RELAY-2
Relay peripheral board with 2 power relays. Normally Open and Normally Closed Contacts
Details
MOTOR-1
Stepper motor driver board that allows complete control and drive for a four-phase unipolar stepper-motor up to 1.25A current per phase
Details
TERMINAL-1
Brings out input/output ports of the I/O expansion socket on the base microcontroller board to screw terminal blocks for easier access
Details
Standoff Kit-1
MINI-MAX series of micro-controller boards accept a wide range of peripheral boards that can be plugged to the micro-controller board. The standoff kit consists of 12 pieces of plastic screws and spacers
Details
PROTO-1
Prototyping board with a 20-pin universal expansion connector. Using PROTO-1, analog inputs/outputs, temperature sensors, relays, displays and many other circuits can be added to the base microcontroller board for rapid project development
Details
BRD-EXP-PLLU3PI
Expansion board to connect BiPOM Microcontroller and Peripheral boards to Pololu 3pi robot.
This kit includes a 2x7 female header, an extended 2x7 male headers, two extended 2x1 male headers, two 2x1 female headers, four 7/8" nylon spacers, and four screws for the spacers.
Details
BRD-EXP-PLLU3PI-PS
Expansion board to connect BiPOM Microcontroller and Peripheral boards to Pololu 3pi robot, 5V on-board power supply.
This kit includes a 2x7 female header, an extended 2x7 male headers, two extended 2x1 male headers, two 2x1 female headers, four 7/8" nylon spacers, and four screws for the spacers.
Details
BRD-EXP-PLLU3PI-ZB
Expansion board to add Zigbee ( XBee® ) wireless capability to Pololu 3pi robot.
This kit includes a 2x7 female header, an extended 2x7 male headers, two extended 2x1 male headers, two 2x1 female headers, four 7/8" nylon spacers, and four screws for the spacers.
Details
3pi Expansion Kit with Cutouts
This kit gives you everything you need to add a second level to your 3pi robot. The red printed circuit board has cutouts that let you view the LCD below and make it easier to reach the power button, reset button, and programming header.
Details
3pi Expansion Kit without Cutouts
This kit gives you everything you need to add a second level to your 3pi robot. In this version, the LCD pins are brought up to the expansion board from the base via extended headers for your own custom use. This red printed circuit board can also serve as a general-purpose round prototyping board.
Details
